毛片免费观看,国产综合福利,欧美野外性xxxxxx视频,丰满又黄又爽少妇毛片免费看软件,免费av毛片,国产一级毛片国语一级,毛片大

歡迎訪問濟南立強模具有限公司!

當前位置:首頁-新聞中心-公司新聞濟南注塑模具回彈是什么原因?

濟南注塑模具回彈是什么原因?

來源:http://gxhuafei.com/ 日期:2022-02-26

在注塑加工中有時模具開到底后還會彈回20mm左右,這里濟南注塑加工廠就來說說注塑模具回彈是怎么回事?
In injection molding, sometimes the mold will bounce back about 20mm after it is opened to the end. Here, Jinan injection molding factory will talk about the rebound of injection mold?
1.開模行程設定不合理,緩沖速度壓力太大,位置太小。
1. The setting of mold opening stroke is unreasonable, the buffer speed pressure is too large, and the position is too small.
2.開模油缸有空氣也會有此現象。
2. This phenomenon also occurs when there is air in the mold opening cylinder.
3.應該是在頂出時慢慢爬行20mm吧,如果是這樣就檢查合模閥。
3. Crawl slowly for 20mm during ejection. If so, check the clamping valve.
4.先查換向閥中位情形及油缸密封件.還有壓力的斜率
4. Check the center position of the reversing valve and the sealing parts of the oil cylinder first And the slope of pressure
5.通過沉頭螺絲調節開合調節開合模換向閥內部導引油小孔子(X、Y)可緩解
5. Adjust the opening and closing by countersunk screws. The small Confucius (x, y) in the opening and closing die reversing valve can be relieved
6.還有可能是油箱空氣濾芯堵塞排氣不暢!
6. It is also possible that the air filter element of the oil tank is blocked and the exhaust is not smooth!
濟南注塑模具
7.開鎖模油缸內泄.檢查活塞密封圈和活塞與活塞桿之間螺紋內泄。
7. Internal leakage of unlocking die cylinder Check the internal leakage of the piston sealing ring and the thread between the piston and the piston rod.

相關產品 / Related products

濟南立強模具有限公司

魯ICP備15002024號-2

網站地圖    TXT    XML 魯公網安備 37010502002026號
手机| 广水市| 广丰县| 南充市| 慈溪市| 临安市| 英吉沙县| 泸定县| 水城县| 昌平区| 扎鲁特旗| 江陵县| 长子县| 吉隆县| 都昌县| 南川市| 桂平市| 西昌市| 晋城| 肃南| 英山县| 璧山县| 平邑县| 会昌县| 册亨县| 楚雄市| 皮山县| 南和县| 赣榆县| 平乐县| 永善县| 海兴县| 东明县| 兰州市| 许昌市| 卢龙县| 阿拉善左旗| 河源市| 太谷县| 安义县| 定日县|